Club Chopper Forums Industrial Parts House  

Go Back   Club Chopper Forums > GENERAL CHOPPER TALK AREA > Chopper Builder's Log > One Off Custom Builds

Welcome to Club Chopper!  The World's largest and coolest place to be on the net if you dig the following!

  •  » Custom Bikes
  •  » Killer Paint
  •  » Old School Craftsmanship
  •  » Building and Wrenching
  •  » Hot Babes
  •  » Chopper Build Logs

...then you have come to the right place!

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

Chopper Tech
Tech Article
Tech Article
Tech Article
Tech Article
Tech Article
Main Menu
Module Jump:
Club Chop Gallery

Club Chopper Gallery

Submit Your Photos!

Active Threads
F-Bomb
Last Post: tattoo72
Posted On: Today
Replies: 5
Views: 102
SAT Motorsports rigid attempt.
Last Post: JamesS
Posted On: Today
Replies: 64
Views: 16,311
2007 Pro street sled "sprocktor"
Last Post: fegarex
Posted On: Today
Replies: 5
Views: 122
Merch 560Q cam specs?
Last Post: Spade115
Posted On: 09-13-2021
Replies: 1
Views: 112
Newbie in Phoenix
Last Post: pushrod243
Posted On: 09-11-2021
Replies: 3
Views: 2,142
More...
  #61 (permalink)  
Old 08-18-2021, 08:17 PM
Club Chopper Member
Visit my Photo Gallery
 
Join Date: Jun 2020
Location: Van Anda, BC
Posts: 77
Not Ranked     
Frame and accy's into gloss black:


And a cool dual USB port with led volt meter:

Steadily forward.
Reply With Quote
Sponsored Links
  #62 (permalink)  
Old 08-19-2021, 01:58 PM
Junior Member
Visit my Photo Gallery
 
Join Date: Aug 2021
Location: Cedar Vale, Q
Posts: 18
Not Ranked     
Quote:
Originally Posted by JamesS View Post
Thanks for lookin'

Convenience is not high on the list for a custom builder.
Doing it easy is , well , too easy.
And generally creates bikes that are of singular use and attractive to the builder mostly.
The work done and the experience of dedicated custom builders is not to be easily dismissed.

FINALLY the oil tank is tigged and airtight. A whole lotta patience required to get there. Its ugly as hell , not something I would use on a personal build , but it will work and is pretty much invisible on the finished machine. I'll find a 'hammered' or textured paint to finish it with , wrinkle black or such will hide some of the imperfections.
Here the tank and the battery box are placed in a tub , CLR is introduced , water to fill , and placed in the sun. The CLR will clean the steel and etch it for the primer to come. It will also create a no rust etching inside the tank . Placing the tub in the sun to heat it will accelerate the process.We did this to gas tanks at the chopper shop where I worked. The treatment works great for any new construction or repair work.
Good work I am enjoying the progress.
I was thinking of using vinegar instead of CLR do you know if that will work OK??
Keep up the good work
Reply With Quote
  #63 (permalink)  
Old 08-19-2021, 04:19 PM
Club Chopper Member
Visit my Photo Gallery
 
Join Date: Jun 2020
Location: Van Anda, BC
Posts: 77
Not Ranked     
Thanks for lookin'
Vinegar will work , in a hundred years.
CLR gets it done in a reasonable amount of time.
Reply With Quote
Sponsored Links
  #64 (permalink)  
Old 09-09-2021, 01:51 PM
Club Chopper Member
Visit my Photo Gallery
 
Join Date: Jun 2020
Location: Van Anda, BC
Posts: 77
Not Ranked     
Frame inside the house for now on a stump.
Under seat wiring plate finished and installed:



And time and care was taken to assemble a set of mounting hardware , consisting of chrome 10/24 acorns , washers and allen bolts.
Mounted are the horn , ignition , starter relay and the main circuit breaker , nicer when the work is laid out prior to final finish' being in place.
Reply With Quote
  #65 (permalink)  
Old Today, 03:47 PM
Club Chopper Member
Visit my Photo Gallery
 
Join Date: Jun 2020
Location: Van Anda, BC
Posts: 77
Not Ranked     
Thanks for lookin'.

Electrical assy continues with the install of the led turn sigs. These are red for lighting /brake and yellow for the turn signals.
Look ok:

And the rear axle , an important piece , supplied as a hardened steel rod with threads on either end. I know how critical it is to have the rear axle stable and secure. Looking to the stock Harley item we see one end with a nut welded on. As I was looking at the parts making a plan , I noticed that rectangular washers would help keep the axle from turning.
So I made some 1/8" washers , welded a nuit on one end ofthe axle trapping the washe in place , I then tigged the washer to the nut:


And installed you can see the axle will have a tough time rotating if it came loose:

I may take the other rectngular washer and make a lock plate for the end with the nut.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -7. The time now is 05:39 PM.


vBulletin skins developed by: eXtremepixels
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.6.0

CC Policy

The representations expressed are the representations and opinions of the clubchopper.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners or moderators. clubchopper.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you or have been given the expressed written consent to post. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). For full policy, please click the "CC policy" link. Thank you for visiting the clubchopper.com
Links monetized by VigLink